The white glue you need is divided into 2 categories according to usage habits,
Durable, for ordinary situations
Delicate type, better ink adhesion effect, suitable for fine logos, higher precision patterns, slightly less durable
Which one you like?
3 grades of anti-static pad printing glue
3rd power, 20$/Kg
6th power, 23$/Kg
9th power, 30$/Kg
It is sold in the same way as the German Wacker brand, for example, 9kg glue + 1kg curing agent (A+B) is sold as 10kg
Lenses or other products? Are there any special requirements? Use 9 power anti-static glue for anti-static of mobile phone lens
6th power anti-static glue for counterfeit lenses
Different factories in the same lens industry have different requirements
25kg, 200kg plastic drum optional
The sales price is related to the batch size
100% anti-static function;
Ink can be applied directly without cleaning;
Good deinking and not easy to deform;
The printing effect is good, it is not easy to draw, and the pores are not easy;
long lasting.
912 Operation Instructions
Step 1: prepare the original silicone pad molds
Clean the mold with detergent and dry it by a piece of cloth or an air gun and then coat the mold with a layer of release agent.(The release agent could be Vaseline,detergent,liquid wax or suds).
Make sure your original molds smooth and Clear .
Note: TM912 is a kind of condensation silicone ,Since you start to test our condensation cure silicone before,please make sure that you have cleaned the tools if you use it for addition silicone before.
Step2: Mix part A and silicone oil
Usually the original hardness of the TM912 is around 30 shore A , you may add silicone oil to adjust the hardness , when adding 2% silicone oil , the hardness will reduce 1 shore A .The percentage of silicone oil added should be not more than 30% . Adding silicone oil into the part A and mix it evenly
Step3:Add part B into the mixture of Part A with silicone oil and mix them evenly.
＊Notes:After the Step 2 by adding and mix the silicone oil evenly ,add catalyst into the mixture (The mixing ratio is 100:3. That means the total weight of mixture of Part A and silicone oil : Catalyst should be 100:3 ) and mix them evenly .
1.Weigh the exactly weight by electronic weight. If not , for example add two much Part B, the operation time will be too fast to operate ,which will cause difficult to operate .
2.Mixture should stir evenly.
Otherwise the silicon rubber will be partly solidified and this will give birth to difficulties in your final operation. What’s more, the finished molds will meet a short life. All of these will cause a waste of silicon rubber.
Step4: Vacuum pumping
Without exception, this step takes less than 10 minutes. Otherwise, it will cause cross linking reaction, and no more further steps will be available.
Step 5: Pouring the mixture into the original mold
＊Notes:1. Put an wooden borad on the surface of the silicone pad and set an hole on the board to make sure the board will closely stick on the pad .
2.Wait till the silicone pad totally cured before put into production.
Warm tips:
The general operation time (pot time) is about 30~40 minutes, and the demoulding time is about 3-4 hours under the room temperature of 25℃.
The white and green anti-static styles ，both are also organic silicon rubber
The blending ratio is already in line with the factory default. You can use it by adjusting the ratio.
The softness and hardness of the rubber head must be test by the customer himself.
Glue + silicone oil + curing agent
The curing agent only has a curing effect.
For example,
type 1: the ratio of 9:1 is 90% of glue and 10% of curing agent.
type 2: A clean disposable water cup is used as the container, and the white glue is added with a curing agent of 2% to 3% by weight.
Customers determine the silicone oil themselves. The proportion of silicone oil determines the softness and hardness of the product.
mexico ups 6kg glue 100usd
mexico ups 30kg ink 378usd
flammable and explosive chemical products cannot be transported by ordinary fedex, so they must be transported through special channels for chemical industry. If you cannot find a suitable freight forwarder,
Solution 1, the ink has a long life, I can sell it in another way, the mixed glue paste can not be sold any more and must be used in time, our freight forwarder quoted freight today, the first delivery, freight from existing The amount is deducted, the balance is returned, or deducted from other new orders.
Solution 2, all use our forwarder, prepaid freight to us, you prepaid after we quote the freight
solution 3,wait you find special channels for chemical industry
FedEx
cant direct shipping without
Aviation safety transportation condition appraisal certificate,
each category needs to be tested once to issue a certificate, the cost of a certificate is 460 RMB, a total of 21 categories, the total testing fee is about US$1380
This is a flammable and explosive product, and it is almost impossible to pass the test. Can't get the certificate,
Usually the transportation is through TNT chemical professional channels, or by sea. I suggest you change channels. Or use our forwarder?
206 Lemon Yellow, 304 Rose Red These two colors .The inventory has been bought by another customer. There is no toner at present, and the inks of these two colors cannot be produced temporarily, and these two colors are rarely needed by customers.
